XADO gel revitalizant for gasoline LPG engines 9 mlXADO Gel Revitalizant for Gasoline Engines is an engine treatment that rebuilds worn metal, and protects treated metal from future wear. One 9ml tube contains 33% (RF33) of the active ingredient necessary for 1 complete revitalization cycle. This product is the predecessor to XADO 1 Stage Engine Revitalizant 27ml tube. This treatment is optimized for use in gasoline-powered engines. This product is beneficial for users who wish to add extra Revitalizant in small portions to their automobile engines, or for those who wish to Revitalize using a three-step method adding one tube every few hundred miles.
Revitalizant is unlike any other engine treatment, because it actually works to rebuild metal, targeting the source of engine wear instead of merely masking the symptoms. Since Revitalizant is not a lubricant, you do not have to add this to your car over and over again. Revitalizant is activated by high-heat and friction, so it only repairs metal in high-friction points where metal wear occurs. Revitalizant leaves crank-cases and non-friction metal unaffected. Just three (3) 9ml tubes will provide 1 complete revitalization cycle that will last for 62,000 miles. Optimized for use in gasoline powered engines.
|
General characteristics of the cermet layer:
Microhardness – 750 kg/mm2;
high corrosion resistance;
roughness Ra up to 0,06 mkm.
Treatment of the engine with the oil system 3-10 liters.
Step 1
1. Squeeze out the contents of one tube into the oil mouth of the engine warmed up to the running temperature. Start the engine and let it idle for 5-10 minutes.
Step 2
Do as described in Step 1 after 100-250 km run
Step 3
Do as described in Step 2 after 100-250 km run
Oil system volume, L | 3-10 | 11-20 | 21-30 |
Tubes (9 ml), pcs | 3 | 6 | 9 |
Treatment scheme | 1+1+1 | 2+2+2 | 3+3+3 |
Tubes for new engines | 2 | 4 | 6 |
Do not change oil until the end of the treatment!
Revitalization is considered to be completed after 1500 km run.
Treatment can be done at idling (4 hours are equivalent to 200 km run);
New engines should be treated in one step – 2 tubes at one time.
The protective cermet coating forms on any operative mechanism; in case the mechanism (engine) is in critical state (wear 100%) worn parts must be replaced.
XADO Gel Revitalizant for Gasoline Engines works in gasoline-powered engines of passenger cars and small trucks and 4-stroke motorcycles.
Can be combined with all types of motor oils, from full synthetic to mineral oils.
It takes 600 to 900 miles to complete the Revitalization cycle, during which changing oil is NOT recommended.
Revitalization is considered to be completed after the mileage not less than 932 mi.
Repeated application of Gel Revitalizant for Gasoline Engines is recommended after 62,000 miles.
Processing can be done at idle run (4 hours are equivalent to 124 mi);
New engines with the mileage 12, 427 mi should be processed in one step – 2 tubes at one time.
An engine after a major repair should be processed in 3 stages regular procedure.
The processing of LPG engines is similar to the processing of gasoline engines.
The protective cermet coating will be formed on any operative mechanism; but if the mechanism (engine) is in a critical state (wear-out for 100%) worn-out parts must be replaced.
Restores and protects friction parts of the cylinder-piston group, crank and gas distributing mechanisms against wear;
reduces fuel consumption (by up to 30% at idling, up to 15% under normal driving);
restores lost oil pressure;
regains and increases compression in cylinders;
increases horse power, improves acceleration capability;
decreases noise and vibration level by 10 times;
extends service life of parts by 2-3 times;
protects the engine from negative consequences of cold start;
improves engine operation in 50-100 km run (approx. 20-60 miles);
enables the engine to run up to 300 km (approx. 200 miles) in the event of substantial loss of oil in the system.